Replacing a bath with a walk in shower can make washing easier and release useful space, but a low threshold depends on the floor and drainage beneath it. Plan the whole room around the person using it before selecting a tray, screen or tile finish.
Planning a Walk In Shower in Swansea
Start with the reason for the conversion. You may want easier entry, more standing space, room for a seat or simply a bathroom that suits showering rather than bathing. These priorities can lead to different layouts even within the same footprint.
Explain who will use the shower, whether assistance is needed and whether mobility needs are changing. NHS inform currently reports that one in three people over 65 experiences at least one fall each year. That is a general falls figure, not a bathroom-specific rate or a prediction for an individual. It is a useful reason to take access and floor finishes seriously.
Source: NHS inform: falls figures and context.
Try mapping the routine from entering the room to leaving it dry and dressed. Where would a walking aid stand, where would a helper be, and can the person reach a towel without stepping over anything? A scale plan is useful, but a temporary outline on the existing floor can make pinch points easier to recognise. Do this before choosing an oversized screen that looks impressive in a showroom but compromises movement in your own room.
Decide Between a Tray and a Tiled Wet Room
A walk-in shower usually describes an open entrance, not necessarily a completely level floor. It may use a low tray with a fixed screen, while a wet room uses a waterproofed floor arrangement that directs water to a drain.
Ask the fitter to show the finished threshold height. A tray advertised as slim can still sit on a raised base if the waste cannot fit below floor level. Conversely, a tiled wet room requires a suitable floor structure and waterproofing design; it is not created simply by tiling where the bath stood.
A low-tray proposal and a fully level wet-room proposal should therefore be compared as complete constructions. Ask what preparation each requires, where the waterproof boundary sits and which arrangement best suits the way you will use the room. The less visually dramatic option may meet your priorities with less structural work. Equally, where step-free access is essential, a modest threshold should not be accepted simply because the product description calls it a walk-in shower.

Check Drainage Before Ordering the Shower
The existing bath waste does not prove a new shower can sit flush with the floor. The fitter needs to examine the proposed waste route, space below the floor and the drain's capacity in relation to the shower's flow.
Ask where the trap will be serviced and whether structural work is needed. Avoid assuming joists can be cut to make the design fit. A surface-level plan should be checked against the hidden construction before products are ordered. If a raised tray is necessary, compare that honestly with the access benefit you are trying to achieve.
Make Waterproofing Part of the Specification
Ask for the waterproofing system to be named, including how the floor, wall junctions, penetrations and drain connect. Tiles, grout and visible silicone do not describe the full construction beneath a wet shower area.
Wet-room manufacturer Impey recommends waterproofing its wet-room space and specifies a 1:40 gradient for its floor former to direct water to the waste. This is guidance for that manufacturer's system, not a universal instruction for every tray. Your fitter should follow the selected system's installation requirements and explain which surfaces will be protected.
Source: Impey: wet-room design and waterproofing.
Request photographs of the waterproofing before it is covered. These are useful records of the construction, particularly around the drain and service penetrations. Ask who is responsible for maintaining compatibility between boards, membrane, adhesive and the selected finish. A mixture of products should be an intentional specification, not an assumption that every material carrying the word waterproof works with every other. Keep the care instructions so later drilling or alterations do not accidentally compromise the protected area.
Plan Screens, Controls and Reach
Mark the proposed entrance and screen on the floor plan. Check the route from the doorway, the space for drying and whether water could spray towards the toilet or storage. An open design may need a different screen arrangement from a compact enclosure.
Try reaching the intended controls without stepping into the water stream. Discuss a handheld head, a suitable seat and properly supported grab rails where needed. Towel rails and screens should not become improvised supports. If the room is being adapted for a specific disability, an occupational therapist can help define requirements before the fitter finalises the design.
For a seated user, assess the controls and handset from the seated position, with the screen in place. For somebody receiving help, discuss whether the entrance allows the helper to assist without standing in the spray. These are practical layout checks to work through with the person involved; there is no single grab-rail position or seat height that suits everybody. Confirm the supporting construction while the walls are open rather than adding fixings to an uncertain substrate afterwards.

Choose Finishes for Wet Everyday Use
Compare flooring using its intended wet-use suitability and cleaning requirements, not appearance alone. Ask how the surface performs with soap and water, and whether texture or grout lines create a maintenance burden you can manage.
Check the contrast between the shower edge, floor and nearby fittings if visibility is a concern. Consider where soap, shampoo and towels will go so they do not end up on the floor. A beautiful room that needs bending, stretching or stepping around loose storage may miss the practical purpose of removing the bath.
Agree Disruption and the Final Checks
A conversion may involve plumbing, flooring, waterproofing, wall finishes, ventilation and electrical coordination. Ask which tasks are included and whether the toilet will remain available. Product curing times affect when the shower can first be used; obtain instructions for the actual materials fitted.
- Confirm the finished entry height and clear opening.
- Ask how drainage and water containment will be checked.
- Identify access for future cleaning and maintenance.
- Keep waterproofing and product care information.
Price the complete usable room, including making good where the bath has been removed, rather than comparing tray-and-screen prices alone.
Before accepting the room, ask for the shower to be demonstrated under normal use while the fitter checks drainage and water containment. Confirm how the trap can be cleaned and which seals need inspection. Discuss whether a nearby cabinet or doorway is exposed to splashing. If the room must remain accessible during later maintenance, establish how serviceable fittings can be reached. Good access is a continuing feature of the design, not just the absence of a bath edge on day one.
Sources and Figures
Sources checked on 6 November 2026. Published statistics retain their stated reporting period; illustrative calculations are labelled in the text.
Summary
A successful bath-to-shower conversion brings together drainage, waterproofing, reachable controls and a safe route into the shower. Discuss your bathroom layout and access priorities with Owl Plumbing And Heating before choosing the fittings. Our bathroom fitting service covers Swansea and Llanelli; tell us who will use the shower and the access you want to achieve.
